Section 1 of 2 - Prev - Next
Archive-name: car-audio/part1
Rec-audio-car-archive-name: FAQ/part1
Version: 4.54
Last-modified: 05 March 2004
This is rac-faq.info, produced by makeinfo version 4.5 from
rac-faq.texi.
rec.audio.car Frequently Asked Questions
****************************************
$Revision: 4.54 $
March 2004
This is the FAQ list for the Usenet newsgroup rec.audio.car, maintained
by Ian D. Bjorhovde , with contributions from
many other people (see Section 8). The contents of this document are
based on the contributors' opinions; neither the contributors nor the
FAQ maintainer accept any responsibility or liability for any damages
brought about by the information contained herein.
This document may be freely distributed and reproduced as long as it
remains wholly unaltered and includes this notice. If you do
redistribute this document, especially on a commercial basis, please
contact the FAQ maintainer before doing so.
If you have suggestions for improvements to this document, or if you
fail to understand any part of it, please feel free to send a note to
the FAQ maintainer or to the author of the relevant section. The
initials of the author(s) of each section can be found in brackets
following each question.
This document is posted once per month to the Usenet newsgroups
rec.audio.car, rec.answers, and news.answers, and is available via
anonymous FTP from:
It is also available on the World Wide Web (WWW) and can be accessed
using the URL
If you do not have access to FTP or a WWW client (such as Mozilla or
Internet Explorer) and cannot find the FAQ on any of the aforementioned
newsgroups, you can obtain the FAQ via email by sending email to
with the following three lines in the
message body:
`send usenet/rec.audio.car/FAQ/part1'
`send usenet/rec.audio.car/FAQ/part2'
`send usenet/rec.audio.car/FAQ/part3'
`send usenet/rec.audio.car/FAQ/part4'
`send usenet/rec.audio.car/FAQ/part5'
Note that the rtfm.mit.edu server is a very popular machine, and
accordingly, responses to requests may be slow, especially via the
mail-server. Please be patient when using this service.
Changes to this document are listed in the last section. *Note
Changes::.
Table of Contents
*****************
1 Definitions
1.1 What do all of those acronyms mean?
1.2 What is meant by "frequency response?"
1.3 What is a "soundstage?" What is an "image?"
1.4 What is meant by "anechoic?"
2 Electrical
2.1 My speakers make this high-pitched whine which matches the engine's
RPMs. What is it, and how can I get rid of it?
2.1.1 Level 1: Check out the Amplifier(s)
2.1.2 Level 2: Reduce the System
2.1.3 Level 3: Move the Head Unit
2.1.4 Level 4: Testing the Car
2.1.5 Level 5: Adding Signal Processors
2.1.6 Level 6: Processor Isolation Tests
2.2 My system "pops" when I turn it off. What is happening and how
can I get rid of it?
2.3 What is the best power wire to use?
2.4 What is the best speaker wire to use?
2.5 I heard that I should run my power wire directly to my car's
battery. Why should I bother, and how do I do it?
2.6 Should I do the same thing with my ground wire, then?
2.7 Sometimes when I step out of my car, I get a really bad shock.
What is wrong with my system?
2.8 When my car is running and I have the music turned up loud,
my headlights dim with the music. Do I need a new battery or
a new alternator?
2.9 What is a "stiffening capacitor", and how does it work?
2.9.1 Do I need a capacitor?
2.9.2 Can I just upgrade my headlight wiring instead?
2.9.3 Will the dimming go away if I upgrade the amplifier power/ground
wiring?
2.9.4 What do I look for when buying a capacitor?
2.9.5 How do I install a capacitor?
2.9.6 I have more than one amp in my audio system. Which one should
I have the capacitor run?
2.9.7 Will my bass response improve by adding a capacitor?
2.10 When should I upgrade my battery or add a second battery?
3 Components
3.1 What do all of those specifications on speakers mean?
3.2 Are component/separates any better than fullrange or coaxials?
3.3 What are some good (and bad) brands of speakers?
3.4 What do all of those specifications on amplifiers mean?
3.5 What does "bridging an amp" mean?
3.5.1 Why should I bridge my amp?
3.5.2 Why shouldn't I bridge my amp?
3.5.3 What happens when an amp is bridged?
3.5.4 Does bridging an amp would halve the impedance of the speakers?
3.5.5 Can I bridge my 4 channel head unit?
3.6 What is "mixed-mono?" Can my amp do it?
3.7 What does "two ohm stable" mean? What is a "high-current" amplifier?
3.8 Should I buy a two or four (or more) channel amplifier?
3.9 What are some good (and bad) brands of amplifiers?
3.10 What is a crossover? Why would I need one?
3.11 Should I get an active or a passive crossover?
3.12 Should I buy an equalizer?
3.13 What are some good (and bad) brands of equalizers?
3.14 What do all of those specifications on tape deck head units
mean?
3.15 What are features to look for in a tape deck?
3.16 What are some good (and bad) brands of tape decks?
3.17 What are features to look for in a CD head unit?
3.18 Should I buy a detachable faceplate or pullout CD player?
3.19 What are some good (and bad) brands of CD head units?
3.20 Can I use my portable CD player in my car? Won't it skip a lot?
3.21 What's that weird motor noise I get with my portable CD player?
3.22 What are some good (and bad) brands of portable CD players?
3.23 What's in store for car audio with respect to MD, DAT and DCC?
3.24 Are those FM modulator CD changers any good? What are my other
options?
3.25 What kind of changer will work with my factory head unit?
3.26 What are some good (and bad) brands of CD changers?
3.27 Why do I need a center channel in my car, and how do I do it?
3.28 Should I buy a sound field processor?
3.29 What are some good (and bad) brands of signal processors?
3.30 I keep hearing that speakers for Company X are made by Company
Y. What's the deal?
3.31 What is a Line Driver? Do I need one?
3.32 Can I play MP3 files in my car?
4 Subwoofers
4.1 What are "Thiele/Small parameters?"
4.2 How does speaker sensitivity affect real world SPL? Will a higher
sensitivity give me a larger SPL?
4.3 What are the enclosure types available?
4.4 Which enclosure type is right for me?
4.4.1 Infinite Baffle ("free-air")
4.4.2 Sealed Box
4.4.3 Ported Box
4.4.4 Bandpass Box
4.5 How do I build an enclosure?
4.6 MDF for Dummies
4.6.1 What is MDF?
4.6.2 Where can I get MDF?
4.6.3 What type of saw blade works best when cutting MDF?
4.6.4 What type of router bits work well with MDF?
4.7 What driver should I use?
4.8 Is there any computer software available to help me choose an
enclosure and a driver?
4.9 What is an "aperiodic membrane?"
4.10 Can I use my subs in the winter?
4.11 How can I carpet my enclosure?
4.12 Are large magnets always better than small magnets?
4.13 I know the box volume required for my subwoofer, but what are
the best dimensions for my enclosure?
5 Installation
5.1 Where should I buy the components I want?
5.2 What mail-order companies are out there?
5.3 What tools should I have in order to do a good installation?
5.4 Where should I mount my speakers?
5.5 What is "rear fill", and how do I effectively use it?
5.6 How do I set the gains on my amp?
5.7 How do I select proper crossover points and slopes?
5.8 How do I flatten my system's frequency response curve?
5.9 How do I wire speakers "in series" and "in parallel?"
5.10 Are there any alternatives for Dynamat? It's too expensive!
5.11 How many devices can I attach to my remote turn-on lead?
5.12 How do I wire a relay in my system?
5.13 How do I design my own passive crossovers?
5.14 How do I build my own passive crossovers?
5.15 Can I split the single pre-amp output from my head unit to drive
two amplifiers with a Y-cable?
5.16 How do I turn a stereo signal into a mono signal
5.17 How do I determine a speaker's polarity?
5.18 How can I use an oscilloscope to set the gains in my system?
5.19 Why are kickpanels such a popular location for mounting speakers?
5.20 How can I build custom kickpanels?
5.21 What's worse for a speaker, too much or too little power?
5.22 Why is distortion harmful to my speakers?
5.23 What tools do I need to cut Plexiglas?
5.24 Are there any other special requirements for working with Plexiglas?
6 Competition
6.1 What is IASCA, and how do I get involved?
6.2 What is USAC, and how do I get involved?
6.3 What are the competitions like?
6.4 Should I compete?
6.5 What class am I in?
6.6 Where can I find out when these Sound-Offs are?
6.7 How do I get sponsored by a manufacturer?
7 Literature
7.1 What magazines are good for car audio enthusiasts?
7.2 Are there any newsletters I can read?
7.3 What books can I read?
7.4 Can I contact any manufacturers on-line?
8 Credits
9 Changes
1 Definitions
******************
This section contains background information which defines some of the
acronyms and terminology commonly used in the car audio world.
Understanding these definitions is important in order to understand the
other sections of this document.
1.1 What do all of those acronyms mean? [JSC]
================================================
`A' is for "amperes", which is a measurement of current equal to one
coulomb of charge per second. You usually speak of positive current -
current which flows from the more positive potential to the more
negative potential, with respect to some reference point (usually
ground, which is designated as zero potential). The electrons in a
circuit flow in the opposite direction as the current itself. Ampere
is commonly abbreviated as "amp", not to be confused with amplifiers, of
course, which are also commonly abbreviated "amp". In computation, the
abbreviation for amps is commonly "I".
`V' is for "volts", which is a measurement of electric potential.
Voltages don't "go" or "move", they simply exist as a measurement (like
saying that there is one mile between you and some other point).
`DC' is for "direct current", which is a type of circuit. In a DC
circuit, all of the current always flows in one direction, and so it is
important to understand which points are at a high potential and which
points are at a low potential. For example, cars are typically 12VDC
(twelve volts direct current) systems, and it is important to keep
track of which wires in a circuit are attached to the +12V (positive
twelve volts) lead of the battery, and which wires are attached to the
ground (or "negative") lead of the battery. In reality, car batteries
tend to have a potential difference of slightly higher than 12V, and
the charging system can produce upwards of 14.5V when the engine is
running.
`AC' is for "alternating current", which is a type of circuit in which
the voltage potential fluctuates so that current can flow in either
direction through the circuit. In an AC circuit, it is typically not
as important to keep track of which lead is which, which is why you can
plug household appliances into an outlet the "wrong way" and still have
a functioning device. The speaker portions of an audio system comprise
an AC circuit. In certain situations, it is indeed important to
understand which lead is "positive" and which lead is "negative"
(although these are just reference terms and not technically correct).
See below for examples. The voltage of an AC circuit is usually given
as the RMS (root mean square) voltage, which, for sinusoidal waves, is
simply the peak voltage divided by the square root of two.
`W' is for "watts", a measurement of electrical power. One watt is
equal to one volt times one amp, or one joule of energy per second. In
a DC circuit, the power is calculated as the voltage times the current
(P=V x I). In an AC circuit, the average power is calculated as the
RMS voltage times the RMS current (Prms=Vrms x Irms).
`Hz' is for "hertz", a measurement of frequency. One hertz is equal to
one inverse second (1/s); that is, one cycle per second, where a cycle
is the duration between similar portions of a wave (between two peaks,
for instance). Frequency can describe both electrical circuits and
sound waves, and sometimes both. For example, if an electrical signal
in a speaker circuit is going through one thousand cycles per second
(1000Hz, or 1kHz), the speaker will resonate at 1kHz, producing a 1kHz
sound wave. The standard range of human hearing is "twenty to twenty",
or 20Hz-20kHz, which is three decades (three tenfold changes in
frequency) or a little under ten octaves (ten twofold changes in
frequency).
`dB' is for "decibel", and is a measurement for power ratios. To
measure dB, you must always measure with respect to something else.
The formula for determining these ratios is P=10^(dB/10), which can be
rewritten as dB=10log(P). For example, to gain 3dB of output compared
to your current output, you must change your current power by a factor
of 10^(3/10) = 10^0.3 = 2.00 (that is, double your power). The other
way around, if you triple your power (say, from 20W to 60W) and want to
know the corresponding change in dB, it is dB=10log(60/20)=4.77 (that
is, an increase of 4.77dB). If you know your logarithms, you know that
a negative number simply inverts your answer, so that 3dB corresponding
to double power is the same as -3dB corresponding to half power. There
are several other dB formulas; for instance, the voltage measurement is
dB=20log(V). For example, a doubling of voltage produces 20log2 =
6.0dB more output, which makes sense since power is proportional to the
square of voltage, so a doubling in voltage produces a quadrupling in
power.
`SPL' is for "sound pressure level" and is similar to dB. SPL
measurements are also ratios, but are always measured relative to a
constant. This constant is 0dB which is defined as the smallest level
of sound pressure that the human ear can detect. 0dB is equal to
10^-12 (ten to the negative twelfth power) W/m^2 (watts per square
meter). As such, when a speaker is rated to produce 92dB at 1m when
given 1W (92dB/Wm), you know that they mean that it is 92dB louder than
10^-12W/m^2. You also know than if you double the power (from 1W to
2W), you add 3dB, so it will produce 95dB at 1m with 2W, 98dB at 1m with
4W, 101dB at 1m with 8W, etc.
`THD' is for "total harmonic distortion", and is a measure of the how
much a certain device may distort a signal. These figures are usually
given as percentages. It is believed that THD figures below
approximately 0.1% are inaudible. However, it should be realized that
distortion adds, so that if a head unit, equalizer, signal processor,
crossover, amplifier and speaker are all rated at "no greater than
0.1%THD", together, they could produce 0.6%THD, which could be
noticeable in the output.
An "Ohm" is a measure of resistance and impedance, which tells you how
much a device will resist the flow of current in a circuit. For
example, if the same signal at the same voltage is sent into two
speakers - one of which is nominally rated at 4 ohms of impedance, the
other at 8 ohms impedance - twice as much current will flow through the
4 ohm speaker as the 8 ohm speaker, which requires twice as much power,
since power is proportional to current.
1.2 What is meant by "frequency response?" [JSC]
===================================================
The frequency response of a device is the range of frequencies over
which that device can perform in some fashion. The action is specific
to the device in question. For example, the frequency response of the
human ear is around 20Hz-20kHz, which is the range of frequencies which
can be resolved by the eardrum. The frequency response of an amplifier
may be 50Hz-40kHz, and that of a certain speaker may be 120Hz-17kHz.
In the car audio world, frequency responses should usually be given
with a power ratio range as well, such as (in the case of the speaker)
120Hz-17kHz +/-3dB. What this means is that given an input signal
anywhere from 120Hz to 17kHz, the output signal is guaranteed to be
within an "envelope" that is 6dB tall. Typically the extreme ends of
the frequency range are the hardest to reproduce, so in this example,
the 120Hz and 17kHz points may be referred to as the "-3dB points" of
the amplifier. When no dB range is given with a frequency response
specification, it can sometimes be assumed to be +/-3dB.
1.3 What is a "soundstage?" What is an "image?" [CD]
=======================================================
The "soundstage" is the position (front/back and high/low) that the
music appears to be coming from, as well as the depth of the stage. A
car with speakers only in the front will likely have a forward
soundstage, but may not have enough rear fill to make the music seem
live. A car with both front and rear speakers may have anything from a
forward to a rear soundstage, with an accompanying fill from the softer
drivers depending on the relative power levels and the frequencies
reproduced. The high/low position of the soundstage is generally only
obvious in a car with a forward soundstage. The music may seem to be
originating in the footwells, the dash, or out on the hood, depending
on how the drivers interact with the environment.
The "stereo image" is the width and definition of the soundstage.
Instruments should appear to be coming from their correct positions,
relative to the recording. The position of the instruments should be
solid and easily identifiable, not changing with varying frequencies.
A car can image perfectly with only a center-mounted mono speaker, but
the stereo placement of the music will be absent.
1.4 What is meant by "anechoic?" [JSC]
=========================================
"Anechoic" means not echoing. It usually refers to a style of
measuring a speaker's output which attempts to eliminate echoes (or
"reflections") of the speaker's output back to the measurement area,
which could alter the measurement (positively or negatively).
2 Electrical
*****************
This section describes various problems and concepts which are closely
related to electronics.
2.1 My speakers make this high-pitched whine which matches the engine's
RPMs. What is it, and how can I get rid of it? [IDB]
==========================================================================
The answer to this section was generously provided by David Navone of
Autosound 2000. The material in these instructions was adapted from
the Autosound 2000 Troubleshooting Flow Chart by Ian Bjorhovde with the
permission of Autosound 2000. For more information about Autosound
2000, (see Section 7).
This is a set of instructions to debug a stereo installation if there
is any noise present after it is completed. Follow each step
carefully! If you have more than one amplifier, repeat level one for
each amp to be sure that none of them are responsible for the noise.
2.1.1 Level 1: Check out the Amplifier(s)
------------------------------------------
After you have determined that there is noise in the system, determine
if the amplifier is causing the noise. To do this, mute the signal at
the inputs to the amp by using shorting plugs. If there is no noise,
then the amp is fine, and you can proceed to level 2. However, if
there is noise, then use a test speaker at the amp's output. If this
stops the noise, then the problem is originating in the speaker wiring,
or the passive crossovers. Check to make sure that none of these are
shorting with the body of the car, and start again at level 1. If
noise is still present when using the test speaker, then there may be a
problem with the power supply on the amp. Try connecting an isolated
power supply - if this does not get rid of the noise, then there is
something seriously wrong with the amp, and it should be replaced. If
the noise goes away, then there may be a problem with power supply
filtering or isolation. This can be fixed by changing the amp's ground
point or b adding external supply filtering.
2.1.2 Level 2: Reduce the System
---------------------------------
The amps have been determined to be noise free. If you have any
processors between the head unit and the amps, disconnect them and
connect the head unit directly to the amp. If this gets rid of the
noise, then one (or more) of the processors must be at fault, so
proceed to level 5. Otherwise, try running the signal cables over a
number of different routes. If you are able to find one that does not
produce any noise, permanently route the cables in the same manner, and
proceed to level 5. If not, then you must isolate the head unit from
the car's chassis (except for its ground!) - don't forget to disconnect
the antenna, since it is also grounded to the car. If isolating
the head unit does not solve the problem, the move the grounding point
of the head unit. Hopefully the noise will be gone, and you can
install the head unit with a quiet ground and proceed to level 5,
otherwise go on to level 3.
2.1.3 Level 3: Move the Head Unit
----------------------------------
The amplifiers are fine, but moving both the ground for the head unit
and the signal cables does not solve the noise problem. Take the unit
completely out of the dash, and put it on either the seat or carpet,
and run new signal cables to the input of the amp. If this solves the
problem, re-install the head unit, one step at a time and skip to level
5. But if the noise persists, then move the head unit as close to the
amp as possible and use the shortest possible signal cables. This will
verify that the original signal cables are not causing the problem -
assuming the noise is gone, reinstall the head unit one step at a time
and go to level 5. Otherwise, there may be a problem with the power
filtering for the head unit. As with the amps, power the head unit
with an isolated power supply (again making sure that the head unit
isn't touching the car's chassis at all). If the noise goes away, you
can add power supply filtering or an isolated power supply; go to
level 2. But if the isolated power supply does not solve the problem,
then you can either replace the head unit and go to level 2, or check
the car's electrical system in level 4.
2.1.4 Level 4: Testing the Car
-------------------------------
There does not seem to be a problem with either the head unit or the
amplifier, and the car's charging system is suspect. To see if this is
the case, we can use a system in a car that is already known to be
"quiet." Bring both cars together as if you were going to jump one,
and use jumper cables to connect the two batteries. Start the engine
of the car with the noise problem, and listen to the "quiet" car's
system. If the noise does not go away, there is a SERIOUS problem with
your car's electrical system (possibly a bad alternator). Have a
qualified mechanic check the charging system out. If there is no noise
in the "quiet" car, then the "noisy" car's charging system is
definitely quiet, so continue with level 5.
2.1.5 Level 5: Adding Signal Processors
-----------------------------------------
We have proven that the amplifiers are good, the head unit is good, and
the car's electrical system is good. Now we need to reconnect each
signal processor. Repeat this level for each signal processor used in
your system; if you have added all of your signal processors, and
there is no longer any noise, CONGRATULATIONS! You've removed the
noise from your system! Connect the signal processor. If there
isn't any noise, then go on to the next signal processor. Otherwise,
try re-routing the signal cables. If this cures the problem, the route
them permanently over the quiet path, and install the next processor.
If not, then isolate the processor from the car's chassis except for a
single grounding point. If this works, then permanently isolate the
processor, and move on to the next processor. If isolation does not
help, then advance to level 6.
2.1.6 Level 6: Processor Isolation Tests
------------------------------------------
Now, noise enters the system when one particular processor is
installed, but regrounding it does not help. Move the processor very
close to the amp, and check for noise again. If there isn't any, then
re-install the processor, carefully routing the cables to ensure no
noise, and continue at level 5 with the next processor. Otherwise, use
an isolated power supply to power the processor, making sure that no
part of the processor is touching the car's chassis. If this solves
the problem, the consider permanently installing an isolated power
supply or possibly a 1:1 transformer, and go to level 5 with the next
processor. Otherwise, separate the processor and isolated power supply
from the car by many feet and re- test. If there is still noise, then
there is a serious problem with the processor's design. Get a
different processor, and continue at level 5 with it. If separating
the power supply and processor from the car does solve the noise
problem, then either the processor is damaged, or your tests were
inaccurate. Repeat level 5.
2.2 My system "pops" when I turn it off. What is happening and how
can I get rid of it? [JD]
=====================================================================
This kind of problem is often caused by transients in the signal
processor as it powers down finding their way into the signal path,
which the amplifier then transmits to the speakers.
Usually this can be solved by adding a little turn-off delay to the
processor. This allows the processor to stay powered on for a short
time after the amplifiers have powered down, thus preventing the pop.
Many components sold today (such as crossovers, equalizers, etc) have
delays built-in. Read your manual to see if it is possible to set this
delay on your piece of equipment or be sure to look for this feature
during your next car audio purchase.
If your processor does not have this feature, you can build your own
delay circuit with a diode and a capacitor. Add a 1N4004 diode in
series with the processor's turn-on lead, striped side towards the EQ.
Then add a capacitor in parallel, the (+) side of the cap connects to
the striped (processor) side of the diode, the (-) side of the cap goes
to ground (not the radio or EQ chassis - connect to the car chassis).
Experimenting with the cap value will give you the right amount of delay
before the EQ shuts off. You don't want it too long, just long enough to
make sure the amp is off before the EQ powers down. 220 - 1000 uF is
about right, and make sure the cap is a polarized electrolytic, 16V or
higher. Also keep in mind that the diode will introduce a 0.7V drop on
the remote wire, which can cause the processor to power down before the
rest of the system.
2.3 What is the best power wire to use? [JSC]
================================================
There is much debate over the benefit of certain wiring schemes
(oxygen-free, multistranded, braided, twisted, air core, you name it).
However, most people do agree that the most important factor in
selecting power wire is to use the proper size. Wire is generally
rated in size by American Wire Gauge, abbreviated AWG, or commonly just
Section 1 of 2 - Prev - Next
© 2005 allanswers.org | Terms of use
